JCID P15 Nand Programmer With BGA110 / BGA70

The JCID P15 NAND Programmer with BGA110 / BGA70 Modules is an essential dual-socket programming workstation engineered for micro-soldering labs, logic board diagnostic technicians, and professional iOS device refurbishers. By integrating the PCIe BGA70 module alongside the mainstream PCIe NVMe BGA110 clamping socket, this kit delivers full hardware read, write, deep format, SysCFG repair, and capacity expansion support covering iPhone 6S all the way through iPhone 13 Pro Max, as well as multiple generations of iPad models.

Equipped with an onboard HD OLED real-time status screen, the P15 provides bench technicians with instant visibility over bus voltage, current draw (mA), connection states, and operation progress. Designed for standalone monitoring or direct pairing with the JCID Repair Assistant PC software, the P15 resolves iTunes restore errors, removes factory Wi-Fi unbind locks without motherboard soldering, and manages memory capacity upgrades with high-speed data transfer stability.

Dual-Socket Device & Architecture Coverage

1. BGA70 Socket Module (PCIe Architecture)

• Supported Devices: iPhone 6S, iPhone 6S Plus, iPhone 7, iPhone 7 Plus, iPhone SE (1st Gen); iPad 5 (2017), iPad 6 (2018), iPad 7 (2019), iPad Pro 9.7, iPad Pro 10.5, iPad Pro 12.9 (1st & 2nd Gen).
• Processor Families: Apple A9, A9X, A10, and A10X Fusion platforms.
• Primary Capabilities: High-speed PCIe SysCFG read/write/backup, capacity upgrade (upgrading 16GB/32GB to 128GB/256GB), Wi-Fi unbind without chip desoldering, and deep formatting of bad sectors causing boot loops or iTunes Error 4013.

2. BGA110 Socket Module (PCIe NVMe Architecture)

• Supported Devices: iPhone 8, 8 Plus, X, XR, XS, XS Max, 11, 11 Pro, 11 Pro Max, SE 2, 12, 12 Mini, 12 Pro, 12 Pro Max, 13, 13 Mini, 13 Pro, 13 Pro Max; compatible iPad models.
• Processor Families: Apple A11, A12, A13, A14, and A15 Bionic.
• Primary Capabilities: Advanced NVMe SysCFG partition flashing, storage upgrades (64GB to 128GB/256GB/512GB), one-click Wi-Fi unbind, and deep block formatting to resolve critical iTunes restore errors (Error 9, Error 4013, Error 4014).

Key Capabilities & Engineering Features

• High-Throughput Bus Engine: Engineered with optimized bus lines to drastically cut down NAND reading, backing up, and flashing time compared to earlier generation programmers (JC P13 / P7).
• Direct Storage Capacity Expansion: Upgrade customer devices seamlessly across high-volume repair models by extracting original calibration parameters, formatting fresh high-capacity NAND flash, and writing verified SysCFG profiles.
• One-Click Wi-Fi Unbind: Clear factory Wi-Fi IC binding locks directly from the NAND partition data without desoldering or replacing the motherboard Wi-Fi module.
• NAND Deep Format & Error Repair: Execute low-level factory block formatting on corrupted or bad-block NAND ICs to recover memory chips throwing iTunes restore loops or boot faults.
• Integrated HD OLED Display: Live monitoring of operating current, voltage rails, and system prompts right on the programmer faceplate for rapid hardware-level troubleshooting.
• Non-Removal Purple Screen Diagnostics: Supports USB-connected purple screen mode for reading and editing SysCFG parameters on supported A-series processors without physically desoldering the NAND chip.
• Modular Magnetic Snap-In Dock: Swiftly swap between BGA70 and BGA110 sockets via dual-connector alignment rails without loose ribbon cables or fragile clip connections.

Technical Specification Matrix

Parameter Profile	Specification Details
Product Model	JCID P15 Integrated NAND Programmer Kit
Included Sockets	BGA110 Module + BGA70 Module
Complete Device Scope	iPhone 6S through iPhone 13 Pro Max; compatible iPad / iPad Pro models
NAND Architectures	PCIe BGA70 & PCIe NVMe BGA110 Flash
Core Functions	SysCFG Read/Write/Backup, Capacity Upgrade, Wi-Fi Unbind, Deep Format
Display Type	HD OLED Status & Current/Voltage Display
PC Software	JCID Repair Assistant (Windows 10 / Windows 11 64-bit)
Host Interface	USB Type-C High-Speed Data & Power Ports
Optional Expansions	Supports modular BGA60 and BGA315 sockets (sold separately)

Step-by-Step Programming & Capacity Upgrade Guide

1. Setup & PC Interface: Connect the JCID P15 to your workshop PC using the provided USB Type-C cable and launch the JCID Repair Assistant software.
2. Mount the Target Socket: Snap either the BGA70 (iPhone 6S–7P) or BGA110 (iPhone 8–13PM) module onto the P15 guide pins until seated firmly.
3. Read Original SysCFG: Insert the desoldered original NAND chip into the socket, close the pressure latch, and click Read / Backup SysCFG to store the device's original factory serial numbers, Bluetooth/Wi-Fi MAC addresses, and board calibrations.
4. Prepare Replacement NAND: Remove the original chip and insert the replacement higher-capacity NAND into the socket.
5. Format & Write: Click Format to clear prior block maps, select the target device model, and click Write SysCFG to transfer the backed-up parameters to the new chip.
6. Solder & Clean Restore: Solder the programmed NAND chip onto the logic board and execute a standard clean restore using iTunes or 3uTools.

Package Contents:

• 1 × JCID P15 Programmer Host Unit
• 1 × JCID BGA110 NAND Socket Module
• 1 × JCID BGA70 NAND Socket Module
• 1 × High-Speed USB Type-C Cable

Explain:

• BGA60 module: for iPhone 4/SE-6 Plus Nand flash

• BGA70 module: for iPhone 6S-7 Plus Nand flash

• BGA110 module: for iPhone 8-13 Pro Max Nand flash

• BGA315 module: for iPhone 14-15 series Nand flash